OWC Mercury Elite Pro Dock / DAS Combo: TB3, up to 28 TB, USB 3.0, DP, GbE, SD

OWC has started sales of its new DAS device that can also serve as a Thunderbolt 3 dock. The Mercury Elite Pro Dock is aimed at creative professionals with the latest Thunderbolt 3-enabled laptops that require a significant amount of storage capacity along with a set of traditional interfaces, including USB 3.0 Type-A, DisplayPort, GbE, and an SD card reader.

OWC is a well-known name in the Mac world as for years the company made accessories and upgrades for Apple’s computers. Since modern MacBooks cannot be upgraded, the company had to refocus to docks and now moves forward with its Mercury Elite Pro Dock that also serves as a DAS.

The OWC Mercury Elite Pro Dock is based on Intel’s JHL6540 controller and can be daisy chained with other Thunderbolt 3 devices. On the DAS side of matters, the OWC Elite Pro Dock can pack two 2.5/3.5-inch hard drives and supports RAID0, RAID 1, JBOD, and Span modes to maximize reliability (by mirroring them), double their sequential read/write speeds all the way to ~530 MB/s in case of two 14 TB HDDs (by striping them), or just use them as two separate hard drives or one big drive. RAID is enabled by an ASMedia controller and its mode can be manually switched using a special switch on the back.

OWC plans to offer its Mercury Elite Pro Dock in multiple versions to hit different price and capacity points. All the SKUs will come with two hard drives and offer a 4 TB, 6 TB, 8 TB, 12 TB, 16 TB, 20 TB, 24 TB, and 28 TB capacity.

On the dock side of things, the devices has a GbE port (Intel I210), two USB 3.1 Gen 1 Type-A connectors (Fresco Logic FL1100EX), a DisplayPort 1.2 output, and an SD Card reader (Genesis Logic GL-3227). The OWC Elite Pro Dock can output up to 120 W of power and therefore can power a laptop as well as charge USB devices at the same time.

The OWC Mercury Elite Pro Dock
  General Specifications
Number of Bays 2 bays for 2.5" or 3.5" HDDs
HDD Interface SATA 6 Gbps
HDDs Used Seagate or Toshiba HDDs
Capacities Up to 28 TB
RAID 0/1/JBOD/Span
RAID0 Up to ~530 MB/s (depends on HDD)
RAID1 depends on HDD
Thunderbolt 3 Controller Intel JHL6540
RAID Controller ASMedia controller
GbE Controller Intel I210
USB 3.0 Controller Fresco Logic FL1100EX
Media Card Reader Controller Genesis Logic GL-3227
Ports 2 × Thunderbolt 3
2 × USB 3.0 Type-A
1 × DisplayPort 1.2
1 × SD card reader
1 × GbE
Power Input 100-240V, 50-60Hz
Power Output +12V, 10A
Dimensions Height: 5.8 inches | 147 mm
Length: 9.4 inches | 238 mm
Width: 3.3 inches | 85 mm
Cables Included ?
Software OWC Dock Ejector
Price (MSRP) $320 for DIY kit
$520-$1400 for Drives Included

OWC’s Mercury Elite Pro Dock can be acquired as a DIY kit without any hard drives inside for $319.99 or as a ready-to-go product with two HDDs in RAID 0 inside. The cheapest 4 TB version costs $519.99, whereas the highest-end 28 TB model is priced at $1,399.99. Interestingly, but OWC does not commit to a particular hard drive model or even a manufacturer and ships its device with either Seagate or Toshiba HDDs inside.

Related Reading

Source: OWC

Comments

Post a Comment

Popular posts from this blog

Intel to Discontinue Itanium 9700 ‘Kittson’ Processor, the Last of the Itaniums

Image
Intel on Thursday notified its partners and customers that it would be discontinuing its Itanium 9700-series (codenamed Kittson) processors, the last Itanium chips on the market. Under their product discontinuance plan, Intel will cease shipments of Itanium CPUs in mid-2021, or a bit over two years from now. The impact to hardware vendors should be minimal – at this point HP Enterprise is the only company still buying the chips – but it nonetheless marks the end of an era for Intel and their interesting experiment into a non-x86 VLIW-style architecture. The current-generation octa and quad-core Itanium 9700-series processors were introduced by Intel in 2017, in the process becoming the final processors based on the IA-64 ISA. Kittson for its part was a clockspeed-enhanced version of the Itanium 9500-series ‘Poulson’ microarchitecture launched in 2012, and featured a 12 instructions per cycle issue width, 4-way Hyper-Threading, and multiple RAS capabilities not found on Xeon pr
Read more

Intel Axes 10nm CPU Based NUC

Image
Intel has notified its partners about plans to discontinue its only 10nm small form factor NUC in the market. The NUC, which went under the code name of Crimson Canyon, is/was Intel's only 10nm device in this market - it used Cannon Lake processors made on its 10 nm technology, and paired with AMD’s Radeon 540 graphics.  The fate of Intel’s Cannon Lake processors has been, to put it mildly, 'dead on arrival'. Delayed by over a year because of problems with 10 nm fabrication process, the CPUs suffered low yields and had design selections made that resulted in a non-functioning integrated GPU, as well as high power consumption: the Core i3-8121U processor at the heart of Intel's first generation 10nm ended up in a few China-only laptops ( which we reviewed ), and in a small number of Crimson Canyon NUC devices. Intel advises parties interested in its Crimson Canyon NUC SFF PCs to make their final orders by December 27, 2019, or return them by that date. The f
Read more

Qualcomm Launches the QCA6390 Chipset: 1.8 Gbps Wi-Fi 6 Ready with BlueTooth 5.1

Image
With the upcoming ratification of the Wi-Fi 6 (802.11ax) standard expected in August, a number of companies are gearing up with Wi-Fi 6 ‘ready’ routers and end-points to get the jump on the market. The idea is that the standard won’t change much between now and full ratification, and most companies developing chipsets expect to sail through without issues – the only difference between the companies will be on the ‘optional’ portions of the specifciations. With that, as we saw at Qualcomm’s Tech Day at the end of 2018, the company will be pushing its latest Wi-Fi 6 solutions onto the market. Today is the launch of one of the chipsets, the QCA6390, which also incorporates BlueTooth 5.1.
Read more