HP’s Endpoint Security Controller: More Details About A New Chip in HP Notebooks

One of HP’s key announcements this spring was its revamped security initiative for PCs that includes hardware, software, and deep learning-based approaches. The software and DL parts of the things were discussed earlier this month, but the hardware-based Endpoint Security Controller remained more or less a mystery. This is why we asked HP to talk about it in more detail.

When it was announced, the company said that the HP Endpoint Security Controller is indeed a separate piece of silicon that sits inside HP’s PCs and performs certain security-based tasks. The ESC features a general-purpose processor core, HP’s custom hardware IP blocks, and embedded software. What is interesting is that HP has been installing the controller into its laptops since the EliteBook 800 G1 series launched in 2013, but has been very secretive about it until recently.

Initially, HP used the Endpoint Security Controller only for its Sure Start technology that can 'heal'/recover the system BIOS. Fast forward to 2019, and the controller has gained capabilities. HP now uses it to protect Intel’s Management Engine, and to enable its Sure Run and Sure Recover capabilities.

HP stresses that it is focused to continue to explore features of its ESC to make its HP Elite as well as select HP Pro business computers and select ZBook workstations the most secure mobile PCs on the market. Without disclosing any future plans, HP essentially implies that in the future it can use the Endpoint Security Controller for other security-related features.

HP’s ESC with all the bells and whistles is currently used in the company's sixth-generation EliteBook 800-series as well as HP ZBook 14u and 15u workstations. Eventually, capabilities of the Endpoint Security Controller will migrate to other systems too.

One of the key things about the ESC disclosure is that it shows PC makers are prepared to implement their own hardware-based methods to improve security of their premium PCs aimed at professionals. One would hope that this is a good news, assuming the controllers are sufficiently audited and not just obfuscated, but it will be interesting to see when and if HP incorporates its Endpoint Security Controller into premium consumer and mainstream consumer PCs.

Related Reading

Source: HP

Comments

Post a Comment

Popular posts from this blog

Intel to Discontinue Itanium 9700 ‘Kittson’ Processor, the Last of the Itaniums

Image
Intel on Thursday notified its partners and customers that it would be discontinuing its Itanium 9700-series (codenamed Kittson) processors, the last Itanium chips on the market. Under their product discontinuance plan, Intel will cease shipments of Itanium CPUs in mid-2021, or a bit over two years from now. The impact to hardware vendors should be minimal – at this point HP Enterprise is the only company still buying the chips – but it nonetheless marks the end of an era for Intel and their interesting experiment into a non-x86 VLIW-style architecture. The current-generation octa and quad-core Itanium 9700-series processors were introduced by Intel in 2017, in the process becoming the final processors based on the IA-64 ISA. Kittson for its part was a clockspeed-enhanced version of the Itanium 9500-series ‘Poulson’ microarchitecture launched in 2012, and featured a 12 instructions per cycle issue width, 4-way Hyper-Threading, and multiple RAS capabilities not found on Xeon pr
Read more

Intel Axes 10nm CPU Based NUC

Image
Intel has notified its partners about plans to discontinue its only 10nm small form factor NUC in the market. The NUC, which went under the code name of Crimson Canyon, is/was Intel's only 10nm device in this market - it used Cannon Lake processors made on its 10 nm technology, and paired with AMD’s Radeon 540 graphics.  The fate of Intel’s Cannon Lake processors has been, to put it mildly, 'dead on arrival'. Delayed by over a year because of problems with 10 nm fabrication process, the CPUs suffered low yields and had design selections made that resulted in a non-functioning integrated GPU, as well as high power consumption: the Core i3-8121U processor at the heart of Intel's first generation 10nm ended up in a few China-only laptops ( which we reviewed ), and in a small number of Crimson Canyon NUC devices. Intel advises parties interested in its Crimson Canyon NUC SFF PCs to make their final orders by December 27, 2019, or return them by that date. The f
Read more

TeamGroup T-Force Xcalibur ARGB DDR4-4000 at Computex

Image
At Computex 2019, TeamGroup unveiled a couple of new products aimed at users looking for high-end components. One of these was its refreshed T-Force Xcalibur DDR4 memory now with addressable ARGB LEDs. During CES 2019, TeamGroup announced a set of ASRock Phantom Gaming branded Xcalibur RGB modules , fast forward to Computex 2019, TeamGroup had its new T-Force Xcalibur ARGB on display with the new ARGB heatsinks modelled over a high-end kit of DDR4-4000 Samsung B-Die based memory kit. The T-Force Xcalibur ARGB memory is very similar in design to the previous special edition Xcalibur RGB modules, but with new addressable RGB LEDs which seems to be the new market trend for gaming-focused brands. Each heatsink has a black aluminium finish with the Xcalibur and T-Force logos, with the 120 degrees angled lighting coming from the light bar at the top of the module which includes an Aztec inspired patterning. While TeamGroup only had a DDR4-4000 16 GB (2 x 8 GB) kit on displa
Read more